Sylvan Lake Water Well Depth & Hydrogeology
Regional groundwater summary • GWDrill Historical Log Extraction
Bottom Line Up Front
In Sylvan Lake the median well is 130 feet deep and draws from Sandstone Bedrock bedrock, which supplies 78% of wells here. Water is very hard at about 325 mg/L, so a softener is standard equipment. Rotary drilling is routine and 94% of wells serve ordinary household use. Treatment emphasis: dissolved silica, moderate mineral depth. Porous sandstone favors silica-rich mineral movement.
Modelled Well Depth
130 FT
Median for this area. Typical range 105–150 ft.
Est. Completion Cost
$11,780 CAD
$91/ft effective rate (includes fixed $1,900 mobilization & pump installation).
Water Hardness
325 MG/L
Very Hard. Dissolved silica, moderate mineral depth.
Pump class at this depth: 3/4 HP submersible, 4" casing
Adjust Target Depth
Drag the yellow indicator across the strata bar
Well Statistics
Local measurements compared against Alberta provincial benchmarks.
| Hydrogeological Metric | Local Measurement | AB Provincial Benchmark |
|---|---|---|
| Total Registered Wells | 715 | 1,420 avg per RM |
| Median Well Depth | 130 ft | 118 ft provincial median |
| Average Well Depth | 146.8 ft | 137.1 ft provincial average |
| Recorded Depth Range | 20 – 1410 ft | 2 – 1,201 ft recorded range |
| Dominant Aquifer | Sandstone Bedrock | Mixed glacial till province-wide |
| Estimated Water Hardness | 325 mg/L — Very Hard | 210 mg/L provincial average |
| Est. Drilling Cost Range | $6,610 – $17,260 CAD | $110/ft plus mobilization |
| Domestic Household Use | 94% of wells | 88% province-wide |
Where This Report Applies
Approximate boundary of Sylvan Lake
Shaded area is an approximate municipal outline for orientation only. Well records are aggregated across the entire Sylvan Lake.
Depth Distribution
Most completed wells fall near the median depth of 130 ft.
Median depth of 130 ft falls inside the reported range. Deeper completions here usually mean higher mineral content but steadier year-round pressure.
Aquifer Composition
Bedrock and drift aquifers recorded by drillers in this area.
558 wells Shallow to intermediate glacial drift aquifer deposited in alluvial channels or outwash plains. Yields softer water but requires continuous sediment filtration and shallow bacterial monitoring.
86 wells Low-permeability clay-rich glacial deposits with localized sand lenses. Often slow recharge.
50 wells Major regional bedrock aquifer formed by Ordovician/Silurian dolomite. Known for reliable, high-volume yields with elevated mineral hardness and dissolved calcium/magnesium carbonates.
21 wells Unclassified hydrogeological formation from legacy provincial drill records.
Water Quality Profile
Estimated hardness, mineral risks and treatment implications.
Total Hardness
Very Hard325 MG/L
as CaCO3, Health Canada scale
Present Mineral Risk
- Scale build-up in kettles, heaters and fixtures
- Dissolved iron and manganese staining
- Elevated calcium and magnesium from Sandstone Bedrock bedrock
Test before purchasing treatment. Hardness varies well to well within the same quarter section.
Size custom treatment system for this waterDrilling Activity
Historical permit and construction activity by decade.
63% of wells are over 30 years old. Steel casing installed before 1995 can lose integrity, so any older well should get a casing inspection and a bacterial test before you rely on it.
Data-Driven Prescription
The treatment system this water needs
Generated from 325 mg/L hardness, sandstone bedrock and a 130 ft median completion depth, for a four-person household. Adjust the assumptions in the builder.
Equipment Total
$4,029
Annual Consumables
$549
Softener Sizing
52,000 gr
Water Testing
Tap Score Canadian Essential Water Test
Nothing gets sized without numbers. Regional modelling puts hardness near 325 mg/L in sandstone bedrock, but your own well can sit well off that median.
- Sizing
- Accredited lab panel: hardness, iron, manganese, nitrate, arsenic, total coliform and E. coli
- Equipment
- $349 CAD
- Annual Consumables
- $349 CAD
Iron, Manganese & Sulfur
SpringWell WS1 Air-Injection Iron & Manganese Filter
Dissolved iron and manganese are the routine complaint on sandstone bedrock wells — they stain fixtures and foul softener resin if not removed first.
- Sizing
- Air-injection oxidation, chemical-free, ahead of the softener
- Equipment
- $1,990 CAD
- Annual Consumables
- $60 CAD
Whole-Home Softening
SpringWell SS1 48,000 Grain Whole-Home Softener
At 325 mg/L (very hard) a 4-person household loads roughly 5.7k grains of hardness per day onto the plumbing.
- Sizing
- 52,000 grain metered capacity — about a 7-day regeneration cycle with reserve
- Equipment
- $1,690 CAD
- Annual Consumables
- $140 CAD
Featured Contractor Spot
Are you a licensed well driller serving Sylvan Lake?
Claim your verified listing profile and be found by homeowners on this report.
Instant WellCheck™ Property Dossier
Buying rural acreage or a home in Sylvan Lake? Get an automated 12-page comprehensive property report analyzing all adjacent well logs, lithology strata, aquifer vulnerability, pump test yields, and water hardness risks.
Planning to Drill?
Get three free drilling quotes
Matched to contractors who already drill in Sylvan Lake. Compare casing sizes, depth guarantees, and mobilization fees.
Frequently Asked Questions
Quick answers about water wells in Sylvan Lake.
How deep are water wells in Sylvan Lake?
The average water well in Sylvan Lake, AB is 146.8 feet deep. Most wells range between 105.0 and 150.0 feet.
What is the primary aquifer in Sylvan Lake?
The most common aquifer tapped by drillers in Sylvan Lake is Sandstone Bedrock.