1
Test kit
estimate, confirm with a lab testA test of your own well comes before any equipment. Test for coliform bacteria.
Water testing Manitoba • 240 Registered Wells
Gilbert Plains Municipality Water Well Depth & Hydrogeology
Regional groundwater summary • GWDrill Historical Log Extraction
Bottom Line Up Front
In Gilbert Plains Municipality, the median completed well is 32 ft deep.
A published hardness range for this place and aquifer is under 60 to above 180 mg/L as CaCO₃. That is a regional estimate, not a test of your well. Source: Estimate based on Health Canada hardness bands.
Most production draws from SAND AND GRAVEL (about 39% of local wells).
These municipal aggregates support planning only — they do not replace an accredited laboratory potability test for your own well.
Interactive Well Depth & Geological Stratigraphy (From Local Driller Logs)
Drag the indicator line or tap a geological stratum below to read the recorded depth range
Drilling in: Sand & Gravel Aquifer (15–642+ ft)Glacial Drift Aquifer
Modelled Depth
32 FT
Area median
Drilling cost
$2,240–$4,800
Estimate
Published hardness
under 60 to above 180 mg/L as CaCO₃
0 ft (Surface)Median 32 ft642 ft (Deep)
Topsoil & Surficial Organics
Glacial Drift Silt & Till
Sand & Gravel Aquifer
From local driller logs:
From local driller logs.
Well Statistics
Local measurements compared against Manitoba provincial benchmarks.
Total Registered Wells 240
Median Well Depth 32 ft
MB benchmark: 88 ft provincial median
Average Well Depth 53.8 ft
Recorded Depth Range 10 – 405 ft
Dominant Aquifer SAND AND GRAVEL
Hardness under 60 to above 180 mg/L as CaCO₃ — Estimate. Estimate based on Health Canada hardness bands
Drilling cost $2,240–$4,800 — Estimate. Typical drilling prices in Canada, about $70–$150 per foot
Domestic Household Use 0% of wells
| Hydrogeological Metric | From the registry or a cited study | MB Provincial Benchmark |
|---|---|---|
| Total Registered Wells | 240 | — |
| Median Well Depth | 32 ft | 88 ft provincial median |
| Average Well Depth | 53.8 ft | — |
| Recorded Depth Range | 10 – 405 ft | — |
| Dominant Aquifer | SAND AND GRAVEL | — |
| Hardness | under 60 to above 180 mg/L as CaCO₃ — Estimate. Estimate based on Health Canada hardness bands | — |
| Drilling cost | $2,240–$4,800 — Estimate. Typical drilling prices in Canada, about $70–$150 per foot | — |
| Domestic Household Use | 0% of wells | — |
Where This Report Applies
Approximate boundary of Gilbert Plains Municipality
Shaded area is an approximate municipal outline for orientation only. Well records are aggregated across the entire Gilbert Plains Municipality.
Depth Distribution
Most completed wells fall near the median depth of 32 ft. Recorded depths cover 215 wells.
0–49 ft 68.4% · 147
49–98 ft 17.7% · 38
98–148 ft 7% · 15
148–197 ft 4.2% · 9
197–295 ft 2.3% · 5
295–394 ft 0% · 0
394–591 ft 0.5% · 1
591+ ft 0% · 0
Median depth of 32 ft falls inside the reported range. Deeper completions here usually mean higher mineral content but steadier year-round pressure.
Aquifer Composition
Bedrock and drift aquifers recorded by drillers in this area.
Sand & Gravel Aquifer Glacial Drift Aquifer
39.2% 94 of 240 Shallow to intermediate glacial drift aquifer deposited in alluvial channels or outwash plains. Yields softer water but requires continuous sediment filtration and shallow bacterial monitoring.
Undifferentiated Aquifer Regional Formation
34.2% 82 of 240 Unclassified hydrogeological formation from legacy provincial drill records.
Sedimentary Shale Formation Fractured Shale Aquifer
12.1% 29 of 240 Fractured sedimentary shale formation (including Odanah / Pierre members). Characterized by high total dissolved solids (TDS) and potential sulfur/iron compounds.
Glacial Drift Silt & Till Protective Overburden
10.4% 25 of 240 Dense, low-permeability clay-rich glacial deposits with localized silt lenses. Serves as a natural confining barrier protecting deeper aquifers from surface contamination.
Sandstone Bedrock Formation Basal Bedrock Aquifer
2.9% 7 of 240 Deep basal sandstone bedrock unit (including Winnipeg Formation). Supplies exceptionally stable yields; often exhibits moderate mineral hardness with silica-rich water.
Carbonate Bedrock (Limestone / Dolomite) Primary Bedrock Aquifer
1.3% 3 of 240 Major regional bedrock aquifer formed by Ordovician/Silurian dolomite. Known for reliable, high-volume yields with elevated mineral hardness and dissolved calcium/magnesium carbonates.
185 holes found no usable water. test holes, observation or monitoring wells, dewatering wells, decommissioned wells, dry holes, no-aquifer holes, and other non-supply wells filtered out of the headline
Water Quality Profile
A published hardness range, when one exists for this place and aquifer. Not a test of your well.
Estimate
under 60 to above 180 mg/L as CaCO₃
Estimate. Estimate based on Health Canada hardness bands. Regional estimate, not a test of your well.
Health Canada. Guidelines for Canadian Drinking Water Quality: Operational Parameters.
No measured government test within 25 km. Test your water.
Soft (<60) Med (61–120) Hard (121–180) V. hard (>180)
USGS (2018) bands reprinted by Health Canada. A range can cross more than one band. This is not a sample.
What this is not
- Not a laboratory result for a well on your property.
- Not a reason to size a softener. Size equipment from a lab test.
- Not a drilling quote. A cost line on this page is a national estimate, not a price for one well.
Health Canada has not set a maximum acceptable concentration for hardness. A wide published range can sit in more than one USGS band.
Drilling Activity
Historical permit and construction activity by decade.
Pre-1970 104 wells · avg 58 ft
1970s 28 wells · avg 68 ft
1980s 56 wells · avg 45 ft
1990s 23 wells · avg 50 ft
2000s 19 wells · avg 39 ft
2010s 4 wells · avg 73 ft
2020s 3 wells · avg 88 ft
85% of dated wells are over 30 years old (pre-1995). Steel casing installed before 1995 can lose integrity over time. Any older well should get a casing inspection and a certified bacterial test before reliance.
Treatment
Size treatment from a laboratory test
This page does not turn a hardness range or a well depth into an equipment total, a grain capacity, or a drilling price. Read the methodology, the filtration guide, and the products catalog.
Suggested system
Suggested system for Gilbert Plains Municipality
2
Sediment prefilter
estimate, confirm with a lab testA sediment prefilter is worth considering where wells draw from SAND AND GRAVEL. This follows the aquifer type.
Sediment guide 3
UV disinfection
estimate, confirm with a lab testUV disinfection is worth considering where wells draw from SAND AND GRAVEL. Test for coliform bacteria. This follows the aquifer type.
Bacteria and UV guide Local Contractors
Licensed Water Well Drillers Serving Gilbert Plains Municipality
Because water wells in Gilbert Plains Municipality average 32 ft into sand and gravel, contractors equipped with heavy rotary rigs and proper casing seals are recommended. Contact local drillers directly or request competitive bids.
Formation Drilling Ltd.
Yard: Dauphin, MB (29 km away)
Confirm the contractor's provincial licence before you hire
Parkland Hydrogeology Artesian Flow Control Glacial Drift Screens
Rob Smith & Son Drilling
Yard: Neepawa, MB (125.7 km away)
Confirm the contractor's provincial licence before you hire
Riding Mountain Slopes Delta Sand Aquifers Farm & Acreage Supply
Fred A. Zavislak Well Drilling Ltd.
Yard: Brandon, MB (147.8 km away)
★ 4.5
(8 Google reviews)
Westman Drilled Wells Deep Sand Screens Residential Acreages
Interlake Water Supply Co Ltd.
Yard: Inwood, MB (219.7 km away)
★ 4.0
(4 Google reviews)
Interlake Limestone Bedrock Artesian Flow Relief Pasture Wells
Looking for more regional well drillers?
Explore all registered water well contractors operating across MB.
Featured Contractor Spot
Are you a licensed well driller serving Gilbert Plains Municipality?
Claim your verified listing profile and be found by homeowners on this report.
Frequently Asked Questions
Quick answers about water wells in Gilbert Plains Municipality.
What is the median well depth in Gilbert Plains Municipality?
Among 215 producing water wells with a recorded depth, the median is 32.0 ft (9.7536 m).
Which aquifer is recorded most often in Gilbert Plains Municipality?
The most frequently recorded producing aquifer is SAND AND GRAVEL, on 94 of 240 wells with a producing aquifer name.
Adjacent Municipalities & Nearby Well Records
Explore neighbouring hydrogeological formations and compare drilling depths