Canada's Well Water Guide
Loading regions
Manitoba • 221 Registered Wells

Grandview Municipality Water Well Depth & Hydrogeology

Regional groundwater summary • GWDrill Historical Log Extraction

Bottom Line Up Front

In Grandview Municipality, the median completed well is 45 ft deep.

A published hardness range for this place and aquifer is under 60 to above 180 mg/L as CaCO₃. That is a regional estimate, not a test of your well. Source: Estimate based on Health Canada hardness bands.

Most production draws from SAND AND GRAVEL (about 48% of local wells).

These municipal aggregates support planning only — they do not replace an accredited laboratory potability test for your own well.

Interactive Well Depth & Geological Stratigraphy (From Local Driller Logs)

Drag the indicator line or tap a geological stratum below to read the recorded depth range

Drilling in: Sedimentary Shale Formation (30–120 ft)Fractured Shale Aquifer

Modelled Depth

45 FT

Area median

Drilling cost

$3,150–$6,750

Estimate

Published hardness

under 60 to above 180 mg/L as CaCO₃

0 ft (Surface)Median 45 ft569 ft (Deep)
Glacial Lacustrine Clay & Silt
Sedimentary Shale Formation
Sand & Gravel Aquifer
Sand & Gravel Aquifer
From local driller logs:

From local driller logs.

Well Statistics

Local measurements compared against Manitoba provincial benchmarks.

Total Registered Wells 221
Median Well Depth 45 ft
MB benchmark: 88 ft provincial median
Average Well Depth 62.3 ft
Recorded Depth Range 7 – 330 ft
Dominant Aquifer SAND AND GRAVEL
Hardness under 60 to above 180 mg/L as CaCO₃ — Estimate. Estimate based on Health Canada hardness bands
Drilling cost $3,150–$6,750 — Estimate. Typical drilling prices in Canada, about $70–$150 per foot
Domestic Household Use 0% of wells

Where This Report Applies

Approximate boundary of Grandview Municipality

Shaded area is an approximate municipal outline for orientation only. Well records are aggregated across the entire Grandview Municipality.

Depth Distribution

Most completed wells fall near the median depth of 45 ft. Recorded depths cover 193 wells.

0–49 ft 53.9% · 104
49–98 ft 28% · 54
98–148 ft 10.4% · 20
148–197 ft 4.7% · 9
197–295 ft 2.6% · 5
295–394 ft 0.5% · 1
394–591 ft 0% · 0
591+ ft 0% · 0

Median depth of 45 ft falls inside the reported range. Deeper completions here usually mean higher mineral content but steadier year-round pressure.

Aquifer Composition

Bedrock and drift aquifers recorded by drillers in this area.

Sand & Gravel Aquifer Glacial Drift Aquifer
47.5%

105 of 221 Shallow to intermediate glacial drift aquifer deposited in alluvial channels or outwash plains. Yields softer water but requires continuous sediment filtration and shallow bacterial monitoring.

Undifferentiated Aquifer Regional Formation
33.9%

75 of 221 Unclassified hydrogeological formation from legacy provincial drill records.

Glacial Drift Silt & Till Protective Overburden
9%

20 of 221 Dense, low-permeability clay-rich glacial deposits with localized silt lenses. Serves as a natural confining barrier protecting deeper aquifers from surface contamination.

Sedimentary Shale Formation Fractured Shale Aquifer
8.6%

19 of 221 Fractured sedimentary shale formation (including Odanah / Pierre members). Characterized by high total dissolved solids (TDS) and potential sulfur/iron compounds.

Carbonate Bedrock (Limestone / Dolomite) Primary Bedrock Aquifer
0.9%

2 of 221 Major regional bedrock aquifer formed by Ordovician/Silurian dolomite. Known for reliable, high-volume yields with elevated mineral hardness and dissolved calcium/magnesium carbonates.

149 holes found no usable water. test holes, observation or monitoring wells, dewatering wells, decommissioned wells, dry holes, no-aquifer holes, and other non-supply wells filtered out of the headline

Water Quality Profile

A published hardness range, when one exists for this place and aquifer. Not a test of your well.

Estimate

under 60 to above 180 mg/L as CaCO₃

Estimate. Estimate based on Health Canada hardness bands. Regional estimate, not a test of your well.

Health Canada. Guidelines for Canadian Drinking Water Quality: Operational Parameters.

No measured government test within 25 km. Test your water.

Soft (<60) Med (61–120) Hard (121–180) V. hard (>180)

USGS (2018) bands reprinted by Health Canada. A range can cross more than one band. This is not a sample.

What this is not

  • Not a laboratory result for a well on your property.
  • Not a reason to size a softener. Size equipment from a lab test.
  • Not a drilling quote. A cost line on this page is a national estimate, not a price for one well.

Health Canada has not set a maximum acceptable concentration for hardness. A wide published range can sit in more than one USGS band.

Drilling Activity

Historical permit and construction activity by decade.

Pre-1970 77 wells · avg 48 ft
1970s 31 wells · avg 51 ft
1980s 54 wells · avg 59 ft
1990s 30 wells · avg 86 ft
2000s 17 wells · avg 64 ft
2010s 5 wells · avg 92 ft
2020s 2 wells · avg 152 ft

84% of dated wells are over 30 years old (pre-1995). Steel casing installed before 1995 can lose integrity over time. Any older well should get a casing inspection and a certified bacterial test before reliance.

Treatment

Size treatment from a laboratory test

This page does not turn a hardness range or a well depth into an equipment total, a grain capacity, or a drilling price. Read the methodology, the filtration guide, and the products catalog.

Suggested system

Suggested system for Grandview Municipality

1

Test kit

estimate, confirm with a lab test

A test of your own well comes before any equipment. Test for coliform bacteria.

Water testing
2

Sediment prefilter

estimate, confirm with a lab test

A sediment prefilter is worth considering where wells draw from SAND AND GRAVEL. This follows the aquifer type.

Sediment guide
3

UV disinfection

estimate, confirm with a lab test

UV disinfection is worth considering where wells draw from SAND AND GRAVEL. Test for coliform bacteria. This follows the aquifer type.

Bacteria and UV guide
Local Contractors

Licensed Water Well Drillers Serving Grandview Municipality

Because water wells in Grandview Municipality average 45 ft into sand and gravel, contractors equipped with heavy rotary rigs and proper casing seals are recommended. Contact local drillers directly or request competitive bids.

Formation Drilling Ltd.

Yard: Dauphin, MB (53.6 km away)

Confirm the contractor's provincial licence before you hire
Parkland Hydrogeology Artesian Flow Control Glacial Drift Screens

Rob Smith & Son Drilling

Yard: Neepawa, MB (138.8 km away)

Confirm the contractor's provincial licence before you hire
Riding Mountain Slopes Delta Sand Aquifers Farm & Acreage Supply

Fred A. Zavislak Well Drilling Ltd.

Yard: Brandon, MB (152.9 km away)

★ 4.5 (8 Google reviews)
Westman Drilled Wells Deep Sand Screens Residential Acreages

Interlake Water Supply Co Ltd.

Yard: Inwood, MB (242.5 km away)

★ 4.0 (4 Google reviews)
Interlake Limestone Bedrock Artesian Flow Relief Pasture Wells

Looking for more regional well drillers?

Explore all registered water well contractors operating across MB.

Featured Contractor Spot

Are you a licensed well driller serving Grandview Municipality?

Claim your verified listing profile and be found by homeowners on this report.

Claim Local Listing

Frequently Asked Questions

Quick answers about water wells in Grandview Municipality.

What is the median well depth in Grandview Municipality?

Among 193 producing water wells with a recorded depth, the median is 45.0 ft (13.716 m).

Which aquifer is recorded most often in Grandview Municipality?

The most frequently recorded producing aquifer is SAND AND GRAVEL, on 105 of 221 wells with a producing aquifer name.

Adjacent Municipalities & Nearby Well Records

Explore neighbouring hydrogeological formations and compare drilling depths

Nearby communities